Skip Navigation LinksHome > Cubiczirconia

ABOUT CUBIC ZIRCONIA

Cubic Zirconia (or CZ) is zirconium oxide (ZrO2), a mineral that is extremely rare in nature but is widely synthesized for use as a diamond simulant.  The synthesized material is hard, optically flawless and usually colorless, but may be made in a variety of different colors. It should not be confused with zircon, which is a zirconium silicate (ZrSiO4).

Because of its low cost, durability, and close visual likeness to diamond, synthetic cubic zirconia has remained the most gemologically and economically important diamond simulant since 1976.  Its main competition as a synthetic gemstone is the more recently cultivated material simulated moissanite.

Technical Aspects of Cubic Zirconia
Cubic zirconia is, as its name would imply, crystallographically isometric, and as diamond is also isometric, this is an important attribute of a would-be diamond simulant. Synthesized material contains a certain mole percentage (10-15%) of metal oxide stabilizer. During synthesis zirconium oxide would otherwise form monoclinic crystals, as that is its stable form under normal atmospheric conditions. The stabilizer is required for cubic crystal formation; it may be typically either yttrium or calcium oxide, the amount and stabilizer used depending on the many recipes of individual manufacturers. Therefore the physical and optical properties of synthesized CZ vary, all values being ranges.

It is a dense substance, with a specific gravity between 5.6 - 6.0. Cubic zirconia is relatively hard, at about 8.5 on the Mohs scale - nowhere near diamond, but much harder than most natural gems. Its refractive index is high at 2.15 - 2.18 (B-G interval) and its luster is subadamantine. Its dispersion is very high at 0.058 - 0.066, exceeding that of diamond (0.044). Cubic zirconia has no cleavage and exhibits a conchoidal fracture. It is considered brittle.

Under shortwave UV cubic zirconia typically luminesces a yellow, greenish yellow or "beige." Under longwave UV the effect is greatly diminished, with sometimes a whitish glow being seen. Colored stones may show a strong, complex rare earth absorption spectrum.

Cubic Zirconia (CZ) History
Since 1892 the yellowish, monoclinic mineral baddeleyite had been the only natural form of zirconium oxide known. Being of rare occurrence it had little economic importance.

The extremely high melting point of zirconia (2750°C) posed a hurdle to controlled single-crystal growth, as no existing crucible could hold it in its molten state. However, stabilization of zirconium oxide had been realized early on, with the synthetic product stabilized zirconia introduced in 1930. Although cubic, it was in the form of a polycrystalline ceramic: it was made use of as a refractory material, highly resistant to chemical and thermal (up to 2540°C) attack.

Seven years later, German mineralogists M. V. Stackelberg and K. Chudoba discovered naturally occurring cubic zirconia in the form of microscopic grains included in metamict zircon. Thought to be a byproduct of the metamictization process, the two scientists did not think the mineral important enough to formally name. The discovery was confirmed through x-ray diffraction, proving a natural counterpart to the synthetic product exists.

As with the majority of grown diamond look-alikes, the conceptual birth of single-crystal cubic zirconia began in the minds of scientists seeking a new and versatile material for use in lasers and other optical applications. Its evolution would eclipse earlier synthetics, such as synthetic strontium titanate, synthetic rutile, YAG (Yttrium Aluminium Garnet) and GGG (Gadolinium Gallium Garnet).

Some of the earliest research into controlled single-crystal growth of cubic zirconia occurred in 1960s France, much work being done by Y. Roulin and R. Collongues. This technique involved molten zirconia being contained within a thin shell of still-solid zirconia, with crystal growth from the melt: The process was named cold crucible, an allusion to the system of water cooling used. Though promising, these pursuits yielded only small crystals.

Later, Soviet scientists under V. V. Osiko at the Lebedev Physical Institute in Moscow perfected the technique, which was then named skull crucible (an allusion either to the shape of the water-cooled container or to the occasional form of crystals grown). They named the jewel Fianit, but the name was not used outside of the USSR. Their breakthrough was published in 1973, and commercial production began in 1976. By 1980 annual global production had reached 50 million carats (10,000 kg). See also Russian Star.

Synthesis of Cubic Zirconia
Larry P Kelley monitoring melting zirconium oxide in a furnace to create cubic zirconia.The Soviet-perfected skull crucible is still used today, with little variation. Water-filled copper pipes provide a cup-shaped scaffold in which the zirconia feed powder is packed, the whole contraption being wrapped with radio frequency induction coils running perpendicular to the copper pipes. A stabilizer is mixed with the feed powder, being typically either yttria or calcium oxide.

The RF induction coils function in a manner similar to the primary winding in a transformer. The heated zirconia acts as the "secondary winding" of a transformer which in effect is "shorted" out and thus gets incredibly hot. This heating method requires the introduction of small pieces of zirconium metal. The metal is placed near the outside of the charge and is melted by the RF coils and heats the surrounding zirconia powder from the outside inwards. The cooling water-filled pipes embracing the outer surface maintain a thin "skin" (1-2 mm) of unmelted feed, creating a self-contained apparatus. After several hours the heat is reduced in a controlled and gradual manner, resulting in the formation of flawless columnar crystals. Prolonged annealing at 1400°C is then carried out to remove any strain. The annealed crystals, which are typically 5 cm long by 2.5 cm wide (although they may be grown much larger), are then cut into gemstones.

The addition of certain metal oxide dopants into the feed powder results in a variety of vibrant colors. For example:

Cerium: yellow, orange, red
Chromium: green
Neodymium: purple
Erbium: pink
Titanium: golden brown

Innovations of CZ (Cubic Zirconia)
In recent years manufacturers have sought ways of distinguishing their product by supposedly "improving" cubic zirconia. Coating finished CZs in a film of diamond-like carbon (DLC) or Amorphous Diamond is one such innovation, a process using chemical vapor deposition. See Russian Star. The resulting material is purportedly harder, more lustrous and more like diamond overall: The coating is thought to quench the excess fire of CZ, while improving its refractive index, thus bringing it more in line with diamond. Additionally, because of the high percentage of diamond bonds in the amorphous diamond coating, the finished simulant will show a positive diamond signature under Raman spectroscopy.

Another technique first applied to quartz and topaz has also been adapted to cubic zirconia: Vacuum-sputtering an extremely thin layer of metal oxide (typically gold) onto the finished stones creates an iridescent effect. This material is marketed as "mystic" by many dealers. Unlike DLC, the surreal effect is not permanent, as abrasion easily removes the oxide layer.

CZ (Cubic Zirconia) versus Diamond
Cubic zirconia is so optically close to diamond that only a trained eye can easily differentiate the two. There are a few key features of CZ which distinguish it from diamond, some observable only under the microscope or loupe. For example:

Dispersion. With a dispersive power greater than diamond (0.060 vs. 0.044) the more prismatic fire of CZ can be seen by even an untrained eye.

Hardness. CZ has an 8.5 to 9.0 on the Mohs' hardness scale vs. a rating of 10 for diamonds.

Specific gravity. CZs are heavyweights in comparison to diamonds; a CZ will weigh about 1.7 times more than a diamond of equivalent size. Obviously, this difference is only useful when examining loose stones.

Flaws. Contemporary production of cubic zirconia is virtually flawless, whereas most diamonds have some sort of defect, be it a feather, included crystal, or perhaps a remnant of an original crystal face (e.g. trigons).

Refractive index. CZ has a refractive index of 2.176, compared to a diamond's 2.417.

Cut. Under close inspection with a loupe, the facet shapes of some CZs appear different from diamonds.

In theory, many gems (such as CZs and diamonds) look best when the star facet, crown main facets, and upper girdle facets do not quite meet. (Per Step 11 of editor's note 36 to Marcel Tolkowsky's Diamond Design.) Diamond has such a high refractive index that having these facets meet at a single point does not cause much loss of fire or reflection. Diamonds normally have these facets meet at a point, because that is more symmetrical and reflects well on the cutter's precision. On the other hand, CZ has a considerably lower refractive index than diamond. CZs are often cut with 6-sided crown main facets, so that the star facets do not touch the upper girdle facets. This optimizes the brilliance and fire of the CZs.

The optimum angle of the main crown facets is steeper for diamond than for CZ. (According to Tolkowsky's model of the crown, for a given pavilion angle and girdle thickness). CZs are often cut so that the crown main facets do not touch the girdle. This allows the CZs to have a shallower crown angle, while still having the same crown height as a diamond with a similar cut.

Color. More precisely, the lack of color: Only the rarest of diamonds are truly colorless, most having a tinge of yellow or brown to some extent. By comparison, CZ can be made in most cases entirely colorless: equivalent to a perfect "D" on diamond's color grading scale.

Thermal conductivity. CZs are thermal insulators whilst diamonds are among the most efficient thermal conductors, exceeding copper. This makes telling the difference between diamond and CZ quite easy for those with the right tools.

Caring for Cubic Zirconia
Cubic Zirconia can be cleaned with any conventional jewelry cleaner or detergent.  With such a high hardness and durability, you can use a brush to clean off dirt or oil also.  Ultra clean jewelry cleaners may also be used on CZ and will not damage the stone.  However, when using soap leaving a film that will dull the brilliance of the stone.  Cubic zirconia should be cleaned frequently to remove oils from skin that also dull the brilliance of the gem.

------------------------------------------------------------------------------------------------------------------------------
Source:
Wikipedia contributors. Cubic zirconia [Internet]. Wikipedia, The Free Encyclopedia; 2007 Jan 1, 04:12 UTC [cited 2007 Jan 6]
Available from: http://en.wikipedia.org/w/index.php?title=Cubic_zirconia&oldid=97665489.

");